Het is nu do 28 maart, 2024 22:01


Plaats een nieuw onderwerp Antwoord op onderwerp  [ 78 berichten ]  Ga naar pagina Vorige  1, 2, 3, 4, 5, 6  Volgende
Auteur Bericht
Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: zo 15 feb, 2015 19:00 
HY Forum Super Expert
HY Forum Super Expert
 WWW  Profiel

Geregistreerd: ma 23 jul, 2012 17:34
Berichten: 176
Woonplaats: deer isle , maine
now that i am thinking about this....i had a problem after the rebuild where my oil light would "flicker" at idle but only after about 15 minutes of running. after an hour of running and going about 30 kph the red light would become more and more lit. it seems like the koppakking may have been the problem all along,as water pressure would increase the light would flicker more and more because the coolant was now leaking into the oil and the water in the oil changes its pressure....hmmmm :?: any thoughts?

_________________
'79 HY78, 80 HY 78,'74 HY 72,'88 rhd 2cv,'75 2cv truckette,'69 volkswagen ,2001 Volvo XC,2008 Land Rover
2019 Royal Enfield '81 Moto Guzzi, '67 BSA, '78 Honda 350, '79 Batavus Regency, '81 Benelli Mini Enduro, '80 Garelli
-lelijke Amerikaan


Share on FacebookShare on TwitterShare on DiggShare on DeliciousShare on Google+
Omhoog
 

Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: ma 16 feb, 2015 1:36 
HY Forum Grootmeester
HY Forum Grootmeester
Avatar gebruiker
 WWW  Profiel

Geregistreerd: do 04 sep, 2003 23:59
Berichten: 1725
Woonplaats: Asten (N.B.)
If you ordered and received a new headgasket from Geert (http://www.citroworld.com/tableaux/index.php?pageId=19) then it's absolutely O.K.
But - before getting it all fixed - you should clean all (!!!) surfaces (also inside where the liners-feet are put on) (best with "steel-wool") !
Don't use any fluid gasket !
As Jan W. wrote - the "feet" of all four liners should be (carefully, secure and very well !!) cleaned - and provided with "paper" foot-gaskets (seals); there is is just one (standard) size/thickness you should use.
The HY might seem a "rough machine" but a lot of parts needs quite some "fine-tuning" ! No hurry !

Advice: get out the complete motor and read again all advices I gave you earlier in this topic, step by step.
Finally you will succeed !

Gert

_________________
http://www.youtube.com/watch?v=-B-nGoOZGP4
"Dikke Bertha" (B.M.W. R75/5/1972)"Otje" (HY/1981)"d'Eend" (2CV6 Special/1977)"Valérie" (AZU 250/1974) Munfiets (Simplex herenfiets/1948)


Omhoog
 

Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: ma 16 feb, 2015 13:33 
HY Forum Grootmeester
HY Forum Grootmeester
Avatar gebruiker
 Profiel

Geregistreerd: di 12 aug, 2014 16:31
Berichten: 1064
Woonplaats: Breda
Otje schreef:
.... "paper" foot-gaskets (seals); there is is just one (standard) size/thickness you should use.

Advice: get out the complete motor and read again all advices I gave you earlier in this topic, step by step.
Finally you will succeed !

Gert


For the Traction Avant with the same enine block and liners there is a variety of thickness available to get the liners in the 0,05 - 0,1 mm range

_________________
een Frans "projectje" blijkt een HY Betaillère te zijn, en is eindelijk klaar! en terug naar haar geboortedorp in de Dordogne.
Traction 11 BN 1953
DS 21 IE hydraulique
DS Break ambulance verkocht
XM V6
Fiat Topolino 1938


Omhoog
 

Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: ma 16 feb, 2015 13:52 
HY Forum Grootmeester
HY Forum Grootmeester
Avatar gebruiker
 Profiel

Geregistreerd: di 12 aug, 2014 16:31
Berichten: 1064
Woonplaats: Breda
ugly american schreef:
i have many pictures to upload. cilinderkop is off. otje was right, koppakking :cry: it was niew!
i checked the clearances for the height of the cilinder they were at .005! :)



You wrote 0.005 mm. but I presume and hope you meant 0.05 mm.
I dont understand the numbers on yourefeelergauge. On the picture I can't get a good idea of the clearance.
Measuring the clearances has to be done with an absolute straight steel measuring device. It is neccesary to measure each liner at four different locations to be sure it is absolutely vertical. If you use a longer measuring device it is easier to see some deviations

_________________
een Frans "projectje" blijkt een HY Betaillère te zijn, en is eindelijk klaar! en terug naar haar geboortedorp in de Dordogne.
Traction 11 BN 1953
DS 21 IE hydraulique
DS Break ambulance verkocht
XM V6
Fiat Topolino 1938


Omhoog
 

Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: ma 16 feb, 2015 17:20 
HY Forum Super Expert
HY Forum Super Expert
 WWW  Profiel

Geregistreerd: ma 23 jul, 2012 17:34
Berichten: 176
Woonplaats: deer isle , maine
the feeler gauge is for .051 ! i went around the perimeter of each sleeve and the height was exact for all of them!
when i put the sleeves in i used the paper gaskets with a bit of oil on them ,i got them from geert at citroworld.

_________________
'79 HY78, 80 HY 78,'74 HY 72,'88 rhd 2cv,'75 2cv truckette,'69 volkswagen ,2001 Volvo XC,2008 Land Rover
2019 Royal Enfield '81 Moto Guzzi, '67 BSA, '78 Honda 350, '79 Batavus Regency, '81 Benelli Mini Enduro, '80 Garelli
-lelijke Amerikaan


Omhoog
 

Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: ma 16 feb, 2015 18:06 
HY Forum Grootmeester
HY Forum Grootmeester
Avatar gebruiker
 Profiel

Geregistreerd: di 12 aug, 2014 16:31
Berichten: 1064
Woonplaats: Breda
So, there are not so many possibilitie left for your problem. The headbolts were more or less loose. That must be the reason for the symptoms.Whats left is to figure out why they were loose.

_________________
een Frans "projectje" blijkt een HY Betaillère te zijn, en is eindelijk klaar! en terug naar haar geboortedorp in de Dordogne.
Traction 11 BN 1953
DS 21 IE hydraulique
DS Break ambulance verkocht
XM V6
Fiat Topolino 1938


Omhoog
 

Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: ma 16 feb, 2015 18:16 
HY Forum Grootmeester
HY Forum Grootmeester
Avatar gebruiker
 Profiel

Geregistreerd: do 07 aug, 2003 14:53
Berichten: 2928
Woonplaats: Delft
Did you use the right torque to tighten the bolds? No mistake in kg*m, kN*m, lb*ft, oz*in, or whatever other unit torques can be measured in?


Omhoog
 

Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: ma 16 feb, 2015 21:59 
HY Forum Super Expert
HY Forum Super Expert
 WWW  Profiel

Geregistreerd: ma 23 jul, 2012 17:34
Berichten: 176
Woonplaats: deer isle , maine
hoi ree
ja, beide keren. after 500km i loosened them first and retightened them two times (3 and 6) again. that is why its so strange that they loosened. but i may not have cleared out the oil and water completely as JanW pointed out. also i did use "anti seize compound"

_________________
'79 HY78, 80 HY 78,'74 HY 72,'88 rhd 2cv,'75 2cv truckette,'69 volkswagen ,2001 Volvo XC,2008 Land Rover
2019 Royal Enfield '81 Moto Guzzi, '67 BSA, '78 Honda 350, '79 Batavus Regency, '81 Benelli Mini Enduro, '80 Garelli
-lelijke Amerikaan


Omhoog
 

Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: di 17 feb, 2015 2:11 
HY Forum Super Expert
HY Forum Super Expert
 WWW  Profiel

Geregistreerd: ma 23 jul, 2012 17:34
Berichten: 176
Woonplaats: deer isle , maine
here i am applying the paper gasket to the base of the sleeve with a bit of oil ;

Afbeelding

_________________
'79 HY78, 80 HY 78,'74 HY 72,'88 rhd 2cv,'75 2cv truckette,'69 volkswagen ,2001 Volvo XC,2008 Land Rover
2019 Royal Enfield '81 Moto Guzzi, '67 BSA, '78 Honda 350, '79 Batavus Regency, '81 Benelli Mini Enduro, '80 Garelli
-lelijke Amerikaan


Omhoog
 

Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: di 17 feb, 2015 10:46 
HY Forum Grootmeester
HY Forum Grootmeester
Avatar gebruiker
 Profiel

Geregistreerd: di 12 aug, 2014 16:31
Berichten: 1064
Woonplaats: Breda
Nice clean sleeves and new gasket ; what a joy.
I cant imagine what will go wrong now after the extensive discussions of last days.
Succes!

_________________
een Frans "projectje" blijkt een HY Betaillère te zijn, en is eindelijk klaar! en terug naar haar geboortedorp in de Dordogne.
Traction 11 BN 1953
DS 21 IE hydraulique
DS Break ambulance verkocht
XM V6
Fiat Topolino 1938


Omhoog
 

Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: wo 18 feb, 2015 2:28 
HY Forum Super Expert
HY Forum Super Expert
 WWW  Profiel

Geregistreerd: ma 23 jul, 2012 17:34
Berichten: 176
Woonplaats: deer isle , maine
niew cilinderkop onderweg! :D

_________________
'79 HY78, 80 HY 78,'74 HY 72,'88 rhd 2cv,'75 2cv truckette,'69 volkswagen ,2001 Volvo XC,2008 Land Rover
2019 Royal Enfield '81 Moto Guzzi, '67 BSA, '78 Honda 350, '79 Batavus Regency, '81 Benelli Mini Enduro, '80 Garelli
-lelijke Amerikaan


Omhoog
 

Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: do 26 feb, 2015 7:01 
HY Forum Super Expert
HY Forum Super Expert
 WWW  Profiel

Geregistreerd: ma 23 jul, 2012 17:34
Berichten: 176
Woonplaats: deer isle , maine
Jan W was right, the bolts had to be cleared out better.. this caused my bolts to loosen. i had to pick out the impacted oil and water from inside the bolt holes, i used a vacuum cleaner and a straw to clean them out ,now i wait for the cilinderkop.... 8)

_________________
'79 HY78, 80 HY 78,'74 HY 72,'88 rhd 2cv,'75 2cv truckette,'69 volkswagen ,2001 Volvo XC,2008 Land Rover
2019 Royal Enfield '81 Moto Guzzi, '67 BSA, '78 Honda 350, '79 Batavus Regency, '81 Benelli Mini Enduro, '80 Garelli
-lelijke Amerikaan


Omhoog
 

Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: do 26 feb, 2015 11:10 
HY Forum Grootmeester
HY Forum Grootmeester
Avatar gebruiker
 Profiel

Geregistreerd: di 12 aug, 2014 16:31
Berichten: 1064
Woonplaats: Breda
a story:
in my youth, long ago, I rebuild a FIAT 2300 engine; when I fitted the rocker cover I forgot to clean one bolthole from oil. During tightening the bolt the resistance dropped at a sudden and water poured out of the hole. The pressure has become so high that the bottom of the bolthole was blown away into the waterchannel in the aluminium head. Drilling and a bigger bolt did the trick.

_________________
een Frans "projectje" blijkt een HY Betaillère te zijn, en is eindelijk klaar! en terug naar haar geboortedorp in de Dordogne.
Traction 11 BN 1953
DS 21 IE hydraulique
DS Break ambulance verkocht
XM V6
Fiat Topolino 1938


Laatst bijgewerkt door JanW op za 28 feb, 2015 1:20, in totaal 1 keer bewerkt.

Omhoog
 

Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: za 28 feb, 2015 0:14 
HY Forum Grootmeester
HY Forum Grootmeester
Avatar gebruiker
 WWW  Profiel

Geregistreerd: do 04 sep, 2003 23:59
Berichten: 1725
Woonplaats: Asten (N.B.)
What is the condition of the bolts of the "head" (the thread) ? Not rusted or damaged in any way ? (and indeed: first clean everything all the way before re-building !)
About the gasket: I know Geert personally and he only sells good professional parts for HY (all over the world).
I myself wouldn't copy the idea of Jan W.: letting run the motor without cooling water ... as it isn't required.

_________________
http://www.youtube.com/watch?v=-B-nGoOZGP4
"Dikke Bertha" (B.M.W. R75/5/1972)"Otje" (HY/1981)"d'Eend" (2CV6 Special/1977)"Valérie" (AZU 250/1974) Munfiets (Simplex herenfiets/1948)


Laatst bijgewerkt door Otje op za 28 feb, 2015 0:23, in totaal 1 keer bewerkt.

Omhoog
 

Offline
 Berichttitel: Re: best way to change piston rings?
BerichtGeplaatst: za 28 feb, 2015 0:20 
HY Forum Grootmeester
HY Forum Grootmeester
Avatar gebruiker
 WWW  Profiel

Geregistreerd: do 04 sep, 2003 23:59
Berichten: 1725
Woonplaats: Asten (N.B.)
Oops ... didn't read the very last comments of you both ... :oops:
But I just can't stop repeating: clean ! CLEAN !
CLEAN !!
... before putting back parts together.

By the way: this all is becoming a quit expensive adventure by now ... :wink:

_________________
http://www.youtube.com/watch?v=-B-nGoOZGP4
"Dikke Bertha" (B.M.W. R75/5/1972)"Otje" (HY/1981)"d'Eend" (2CV6 Special/1977)"Valérie" (AZU 250/1974) Munfiets (Simplex herenfiets/1948)


Omhoog
 

Geef de vorige berichten weer:  Sorteer op  
Plaats een nieuw onderwerp Antwoord op onderwerp  [ 78 berichten ]  Ga naar pagina Vorige  1, 2, 3, 4, 5, 6  Volgende


Wie is er online

Gebruikers op dit forum: Bing [Bot] en 4 gasten


Je mag geen nieuwe onderwerpen in dit forum plaatsen
Je mag niet antwoorden op een onderwerp in dit forum
Je mag je berichten in dit forum niet wijzigen
Je mag je berichten niet uit dit forum verwijderen
Je mag geen bijlagen toevoegen in dit forum

Zoek naar:
Ga naar:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group